When a Gotv decoder indicator lights starts blinking, it means there is an issue or a notification which requires the subscribers attention. Most subscribers do not notice or are not aware of the meaning on the Gotv blinking indicators lights. But nothing to worry about as this post will explain explain in details how to carry some necessary troubleshooting steps to fix issues on your gotv set.
How to Fix GOtv decoder showing a yellow/Orange Light Constantly
Carefully follow below steps to fix gotv indicating different colors.
- Step 1: Press the power button
- Step 2: long press the power button, connect the power cable to the decoder with the AV cables or cord and the antennae cable (RF IN)
- Step 3: now 3 lights flashes and then you can remove your hand from the power button
- Step 4: tap p+ p- twice
- Step 6: after that, it will take you straight to the scan process, wait till the decoder completes the scanning and with complete channel list. How to Watch GOtv free on Mobile Phone
Alternatively
if the color blinking persists it means is not receiving sufficient power or voltage is low. Change the power source and if that did not solve the problem, visit the near Gotv Office for repair.
Solution to your Gotv Decoder Blinking Orange Light
The orange light blinking in your GOTV decoder is as a result of a notification sent to your decoder. To view GOTV notification and clear the message, follow these steps below;
- Step 1: simply press Menu
- Step 2: Mail Message
- Step 3: Read /Delete the message
- Step 4: Press the RED button to delete. What To Do When Your Satellite Dish Says No Signal
My Gotv Decoder Shows Orange Light, Stops scanning at 50% on TV
Firstly check if you have at least 60% signal strength and 100% quality for maximum reception. However you may adjust the position of your antenna and ensure that it is high enough and nothing is obstructing it from sky view.
My Gotv decoder is not turning ON, Shows RED Light
Tap on the RED button on your decoder remote. If your device do not turn on after pressing the power button, check if it is connected to power supply. After that check if the power cable is in good condition. If after confirming that your electrical outlet is in proper condition and your GOTV decoder do not turn on yet- take it to the nearest GOtv office for repair.
Gotv Channels not active
You will have to scan. Press Menu > Advanced Options > Installation > Automatics Scan > OK
Gotv Decoder Showing “no service found”
For a quality reception, it is recommended you get a Gotv Antenna.
or
To see your GOTV signal strength progress. Press Menu > Information Central > Signal Strength/Quality. If the signal strength is below 90% and quality below 100%, you will have to check the connections behind your decoder.
Red light on Gotv Decoder
If your GOtv decoder is showing red light, it means your account is disconnected. Pay for your package subscription and get reconnected.
Frenzy valentine is a passionate blogger, developer, and entrepreneur. He is the founder and author of myfreshgists.com and Mycatnails.com.
My Got is on orange indicator for a week now, showing no signal, what should I do
My gotv decoder is blinking green light and I can’t even use my remote
My Gotv is on orange indicator for 3 days now showing no signal. Whats the solution?
My gotv is showing orange light
My gotv is showing a blinking green light with volume bar displayed on the Tv screen. how do i fix it.
Mu decoder is showing orange and red light what might be a problem?
My decoder is doing on and off
Gotv showing only orange colour not coming on, and there is sufficient power supply and remote is working well, but no response from the Gotv when the remote is being pressed.
My gotv decoder show only orange light but not working
My gotv didn’t display on my TV what could be wrong?
Please my gotv is showing only orange color light but does not display, it doesn’t not turn off just that orange color what will I do?
My gotv showing only orange light on decoder and nothing showing on the TV. Please what do I do.
My go tv keep blinking green light and it keep changing channels but when I hold particular number it will show channel but will keep changing channels
My Gotv is going on and off while working I want solutions please
My GOTV keeps showing orange light with no display on the TV I have unplugged and plugged back in but still no display
My decoder is just showing green lite and the green lite is just blinking and didn’t display any channels and the remote can work since the green light is blinking, what should I do?
Confirm you have a sufficient power supply
My gotv blinks red and green lights, the stops it doesn’t display channel and it goes off again and again….. Please what’s the problem with it?
Av travel for a while leaving my gotv decoder unused for about eight months now . I didn’t know why the decoder is only showing red light and not displaying
My gotv is showing only red light how do I fix it
Unplug it from light and plug it back after some minutes
Good morning, please my Gotv decoder is showing only orange color light and nothing more please what should I do
It means you have unread messages, simple go to the message section and check it out
Pls why is my recorder showing red and green and also not coming on?
Try rebooting your decoder. Unplug it from the power source and leave it for five minutes before plugging it back
Goodevening please it been long I subscribed and when I turned my decoder on it showing a standby yellow light, I fixed it again it started working all of a sudden it turned of and showed green, yellow, red light at once , I removed from the plug and fixed it back now it showing yellow light what do I do please am tired already please
Fantastic work like wild fire.I have replaced my GOTV decoder charger it is working very fine.
Was working well before now and after My GOTV when booting start with orange turn green and few second show red,orange and green show orange no signal and start loading again show no signal
My gotv shows green light but doesn’t display anything
Hello Collins, where exactly is the green light showing? If its on the decoder, you should check your connection to the antenna, and if its on screen, restart and update your GOTV software
My go tv red and green light goes on and off and the logo is displayed for a while then disappears
Hello Nancy, this could be as a result of power outage during update. To fix it, reboot your GOTV decoder and then update the software when the options pops out. You can also update it in the settings
Pls when I gotv is on it does not show anything but when I turn it off it slightly shows an orange light
Its signal error, check if the antenna is properly connected. Confirm the rf connector is properly connected at both ends (antenna & tv?)
My gotv is showing a red light without displaying anything on tv, please what di i do???
Hello Jane, adjust your antenna and confirm if its in proper condition
Pls my gotv decorder has been blinking orange color since morning and is showing no signal on TV. What do I do
Check the position of your antenna. Check the coaxial cable and confirm if the f-connector is connected to both the antenna and the decoder
My gotv displays only the logo…
But does it show anything before displaying the logo? If not, the fault could be from the Gotv antenna. Adjust the antenna and ensure it’s not obstructed by any tree or building
Please my gotv decoder is blinking orange light with no signal 📶 on TV.. What can I do
Check the coxial cable, the end that connects to the decoder. Ensure that the small lead inside is long enough. If its not, tear out some outer layer of the coxail cable.
My gotv is showing a red light without any display, what do I do
Check your antenna, there is a loose connection in your antenna, check the lnb cable, tear out the end that connects to your decoder so that the tiny let inside will be long enough to enter your decoder
pls my gotv kips blinking red and green light with out displaying on d tv. What shld I do?
Turn off your decoder, unplug it for 2 minutes, plug it back and turn it on again
My gotv is showing orange light and also showing no signal on tv what should i do
Check ur rf connector and see if its well connected to your decoder. Peal of the cable to make the small thin wire inside to be long
My gotv has Orange. Light and is not displaying what do I do
It went out of signal .. Unplug it and plug it back.. If the case persist, send me a mail at myfreshgists@gmail.com
My gotv is showing a red light without any display, what do I do
A message was sent to me to upgrade my decoder I did so but the decoder keep bringing red light only without any display on the TV
Contact GOTV customer care if the issue persist after turning it off and on again