Step 1
Switch off and remove both the DIRECTV receiver and your television from electric socket. Rotate the receiver around so the back of the device is facing you.
Step 2
Keep your digital antenna not far from the receiver. Plug the antenna’s coaxial connector into the “OFF-AIR IN” ( this can be found at the back of the receiver. You may also choose to use an external digital antenna. Check and recheck the antenna’s manual on proper mounting techniques, then route the antenna’s coaxial cable inside via a window or other opening in your home.
Step 3
Fix the connector tightly with your fingers. Extend the antenna’s aerials and face them toward a window or doorway to get the strongest channel signals available.
Step 4
Connect and power on the receiver and television. Tap on the “Menu” key on your DIRECTV remote control. Use the up and down navigation buttons to navigate to “Settings.” Tap on the “Select” key, then scroll to “Setup” and then press the “Select” key.
Step 5
Scroll to and select “Sat & Ant,” then go to to “Antenna Setup” and click on the “Select” key. Select “Local Networks” and click the “Select” key. Follow the on-screen prompts to select the networks you wish to receive.
Step 6
Scroll to and select “Scan for Channels.” click the “Select” key to begin the scanning process. Immediately the process is done, DIRECTV guide will be displayed so you can delete any channels you don’t want to receive or listed in the guide. How to Program DIRECTV Remote To Tv & fix remote not working
Ways to Use a Direct TV Converter Box for on Air Signal
DirecTV satellite receivers works as a digital converter box if used on an analog television. Using directv local channel connector to obtain DirecTV receiver which can easily receive on-air signals. These signals are your local channels such as CBS, ABC, FOX and NBC. Some other satellite providers do not support local stations, thereby ebabling you to use an antenna to view any local station. Thankfully, you will easily view your local channels by following the step by step methods below.
Step 1
Switch on your television and the DirecTV satellite receiver.
Step 2
Press the “Guide” button on the DirecTV remote control. This shows the station listings for DirecTV.
Step 3
Navigate down the listings. On the left side of tv screen is the station number and channels name. Scroll down until you start getting the local on-air stations. These stations are always found under channel 100.
Step 4
Choose the on-air tv station you want to view and push “Select.” The on-air channel loads onto your TV screen.
Ways to Unlock a Digital Cable Box
Digital cable boxes accesses users to see a large number of digital cable channels on their televisions, which usually can’t house the large number of channels given with cable boxes. Further more, these cable boxes accesses for the use of “parental controls” to lock specific channels and shows from view. Unlocking these channels is an simple process, as long as you have the PIN required to unlock the device.
Step 1
Push the “Menu” button of your cable box remote to access your main menu.
Step 2
Choose the “Parental Controls” option in the main menu.
Step 3
Click on the “Unlock” or “Unlock All Channels” option.
Step 4
Input the PIN into the text box using your remote’s keypad, and click the OK button to unlock the channels on your cable box.
How to Connect an External Antenna to a Dish Network
Its true that some local television channels in specific regions are obtainble to Dish Network subscribers, but not all of the local channels are been offered by the satellite provider. To get local channels that are not obtainable, a Dish subscriber could connect his satellite receiver to any over-the-air antenna with directv local channel connector. Based on the closeness of local TV broadcast towers to your location, a Dish Network subscriber can accept additional channels via an over-the-air antenna without affecting his satellite subscription fee. Easy methods to pay DIRECTV BILL
Connecting Antenna to Dish receiver
Step 1
Ensure that the Dish Network receiver is equipped with an over-the-air (OTA) module. The models that are equipped with the module are; Duo ViP 211 HD receiver, Duo ViP 211k HD receiver, Duo ViP 222 HD receiver, Solo DVR ViP 612 HD DVR, DuoDVR, ViP 622 HD DVR and the DuoDVR ViP 722 HD DVR. Receiver models DuoDVR ViP 722 or Duo ViP 222k HD dont have built-in OTA modules, but subscribers can easily plug the modules from Dish Network.
Step 2
Run a 75-ohm coaxial cable from your indoor or outdoor antenna, and connect it to the “Over The Air Antenna In” coaxial jack in the rear of the Dish Network antenna.
Step 3
Proceed to the on-screen option of the Dish Network receiver, then go to “System Setup,” click on “Local Channels,” and choose “Scan Locals.” When you have finished the scanning process, the number of channels available will be listed. Now press “OK” to go back to the local channel menu.
How Television Is Broadcast to Your Home
Cable TV gets in using a cable that is either plugged in directly to your TV or to a cable box. Here there are two types of signals that can be broadcast: analog or digital. Digital TV can be accessed in your home using cable or over-the-air broadcasts.
Quality of Broadcast
Analog signals have encompass noise and interference thereby making the picture and audio quality sometimes suffers as a result. Digital tv signals are most recent, cleaner signal that results in higher-quality images and audio. Digital TV also comes in two qualities of picture: standard definition (SD) and high definition (HD).
Difference between SD and HD in Digital Cable
Standard definition broadcast is a lower picture quality than high definition. In HD broadcast, the picture is clearer and seems more realistic than in SD or analog broadcasts. Besides picture quality, SD and HD differ in what channels and shows are available in each broadcast format. HD programs such as “SportsCenter HD” will be broadcast as shows that will be best viewed with an HDTV. Some shows may not be available in HD and will be broadcast in SD.
How to View Digital TV through Cable
The first requirement is a television that can display digital broadcasts. To view digital cable, directv local channel connector, a digital cable box, CableCARD or QAM tuner is required from your cable provider or other source. Setup is relatively easy, and cable providers also offer installation service.
Benefits of Digital over Cable (Analog)
Better picture and sound More channels through multi-casting Ability to access more content on video on demand Interactive program guides Ability to record and playback content through Tivo and other related media-playing devices
How to Enable a UPnP 2Wire Router on U-Verse
An AT&T 2Wire router can function as a DSL modem or wireless router, so you can use it with any type of U-verse Internet service. 2Wire provides convenient Web-based configuration to make it easy to enable and configure your new router in minutes. The router’s Universal Plug and Play, or UPnP, feature enables you to join different types of network devices and share files across all of them.
Step 1
Connect one end of an Ethernet cable into one of the router’s LAN ports. There are always three to five of these ports found on the back of the router. Connect the other end of the cable into the Ethernet port of your computer.
Step 2
Proceed to enter the gateway user interface by entering “http://gateway.2wire.net” (without quotes) on the search bar of your Web browser and then click “Enter.”
Step 3
Choose the “Home Network” tab to see a list of the devices on your network. To switch on the UPnP feature, tap on the “Access Shared Files,” and now choose “Enable.” You can then access your files from any computer or mobile device connected to the network.
What do I get with the Local Channel Connector kit?
directv local channel connector kit comes with 4 items:
- An indoor antenna use over-the-air local broadcast stations
- A Local Channel Connector device to join the antenna to Genie models HR44 and HR54
- A power supply unit to socket the Local Channel Connector to an electric outlet
- A directv user guide with setup instructions
What do I do if the Local Channel Connector doesn’t work in my home?
Keep in mind that local channel signals can be very unstable and weak.
Be sure to fix the antenna close to a window in your house.
Signal strength and availability aren’t guaranteed and are disturbed by so many factors, like the weather.
The antenna may not work for everyone.
If you don’t get a signal, look out for your other options. (The antenna is yours to keep.)
Contact us to see if you can get satellite-delivered local channels.
Frenzy valentine is a passionate blogger, developer, and entrepreneur. He is the founder and author of myfreshgists.com and Mycatnails.com.